MPEG LA 16CH Instrukcja Użytkownika

DVQ-2, DMR 4/8/16 RT USER MANUAL1

7) Press “ ” button to display the 4 channels. Press “-” button to change the setting in the menu.8) Press “SEQ” button to activa

2.1.2 PlaybackPress “ ” or “PLAY” button on the front panel, and the device will display the last recorded video.Note: For playback to work properly t

2.2 DVQ-2 Rear Panel1) 75Ω / HI-IMPEDANCE When using LOOP, switch to HI-IMPEDANCE. When not using LOOP switch to 75Ω.2) LOOP / INPUT (For chann

132.2 DMR 4, 8, 16 RT Rear Panel

2.2 DMR 4, 8, 16 RT Rear Panel1) DISK ARRAY PORT: Connect to one disk array for extending HDD capacity.2) IR PORT: Connect to the IR receive

3.0 Installation Guide3.1 Camera and Monitor InstallationThis manual has been carefully written to help you assemble and confi gure your digital video

4. Test each component of your video system prior to installation. Connect each camera directly to the video monitor, using a new power adapter

DVR and Monitor Installation3.2 DVQ-2 SYSTEM CONFIGURATION17

3.2 DMR 4, 8, 16 RT SYSTEM CONFIGURATION18

If your digital video recorder is not working properly: • Not showing any video. • HDD (Hard drive) error messages. • HDD not found. • All

SUPER/CIRCUITS11000 NORTH MOPAC EXPRESSWAYSUITE 300Austin, TX 78759Phone 800-335-9777 • Fax 866-2567-97772

4.2 RECONFIGURE YOUR DVRGo into the main MENU and run the FACTORY DEFAULT, CLEAR HARD DRIVE, and set SYSTEM TIME. Set OVER-WRITE, MOTION DETECTION a

The password screen will appear: NOTE: The default Password is 0000. Simply press the Enter button. To key-in the Password, press the “RIGHT” and “

4.3 RESET DEFAULTSelect ADVANCE> SYSTEM> RESET and press the ENTER button.NOTE: (> = hit the ENTER KEY)Reset all system settings to factory d

Push the LEFT key to select YES and push the ENTER key and confi rm by pushing the ENTER key again to select OK.Set the DVR time and date. CLEAR

4.7 MOTION DETECTIONFrom main MENU select ADVANCE> DETECTION> DETECTION SETUP and press the ENTER key. Select DETECTION, press ENTER key. NOTE:

4.8 RECORD QUALITY AND IPSSelect RECORD from the main menu and press the ENTER key. Set EVENT RECORD ENABLE to YES. RECORD MANUA

Use Table 2 to set your RECORD QUALITY and IPS for DMR 4, 8, 16 RT.DMR-16RT Table 21) Recording time varies depending on: * Different camera qual

Use example below to understand how to setup your IPS and QUALITY settings.EXAMPLE: Setup a DVR to record for 14 days using the FRAME RECORD MODE. Go

5.0 MENU CONFIGURATION5.1 MENU INTRODUCTION28PowerMenuLeft, Right keys SearchUp, Down keysEnter key Plus +, Minus - keysPress the MENU button and ente

The default admin password is 0000. Enter the default password, and press “ENTER”. MAIN MENUThere are 4 options available in the Main Menu:RECORD ---

Please read instructions thoroughly before operation and retain it for future reference. The lightning fl ash with arrowhead

1) MANUAL RECORD ENABLE Start / stop the manual recording.2) EVENT RECORD ENABLE Start / stop the event recording. When enabled the recordi

1) DATE Schedule up to 7 recording days: SUN / MON / TUE / WED / THU / FRI /SAT / MON–FRI / SAT-SUN / DAILY / OFF. Please see example below t

5.6 Camera Advanced camera settings, change camera title, or adjust the brightness. Select “CAMERA”, and press ”ENTER”. 1) TITLE Change the defa

3. Advance motion detection settings. Use AREA to setup motion detection for a selected viewing area. Cameras will pickup areas of movement li

You can also up set up multi-detection areas.Press - MINUS to set the entire area under motion detection.Press + to disable motion detection for the e

NOTE: When using an LCD monitor, and the “MONITOR OUT” setting in the “DISPLAY” menu is set to “MAIN”, the motion detection area setting will be disab

4) LOSS SCREEN Set the video loss screen color (BLUE / BLACK).5) PLAYBACK INFO Position playback information: CENTER or NORMAL 6) DWELL DUR

3) KEY BUZZER Enable or disable sound when pressing buttons on front panel (ON / OFF).4) VLOSS BUZZER Enable or disable sound for video loss

5.11 SystemSelect “SYSTEM”, and press ”ENTER”. 1) SERIAL TYPE Press “ENTER” or “+” / “-” button to set the serial type (RS-485 / RS-232).2)

5.12 NetworkSee Network Section in this manual, page 45.5.13 BackupThe backup fi le can be played in a PC using the supplied licensed Video Server soft

TABLE OF CONTENTSWarning...

5.14 HDD InfoDisplays HDD remaining memory.Select “HDD INFO”, and press ”ENTER”. • AVAILABLE SIZE Display USB fl ash drive capacity. • CHANNEL S

Error Code in “SYSTEM LOG”: Description: 1) SYS ERR 01-YYY #defi ne SYS_ERR_AV087_ERR 1)

6.0 Additional Operation6.1 Key Lock and Unlock• Key Lock On: Press “MENU” + “ENTER” buttons on front panel to lock keys.• AUTO KEYLOCK: Set the tim

6.3 Upgrade(1) Firmware / Multilanguage OSD Upgrade• Use USB to upgrade: Format the USB memory to FAT 32. Get the upgrade fi les from your distribu

6.5 PTZ Camera Setup and Control• PTZ connections, see page 61: • PTZ System Setup: ID, protocol, baud rate setting at the DVR side: See lines 1,2 a

7.0 NETWORKING View video from your PC anywhere in the world by connecting your DVR LAN connection to your network system. 7.1 Things to do

2. Select “NETWORK”, and press ”ENTER”.3. NETWORK TYPE There are 3 network types: STATIC, PPPOE and DHCP. • STATIC Select NETWORK TY

• PPPOE PPPoE needs one “username” and “password” subscribed from ISP provider. NETWORK NETWORK TYPE PPPOE DNS

7.2 Test your connection1. Return to your computer: go to the PC start menu and select “Run”2. Type “cmd” and click “OK”.3. A black box called t

4. The Dos window will display “Reply from” the IP address 3 to 4 times. You will see “Packets sent = X, Received = X and Lost = X. This will

7.0 NETWORKING...45

7.3 Software Installation7.4 Installation1) Install the software: Place the included CD disk into the CD-ROM drive, and install the Video

7.5 Remote Video Server Login Panel2. After setup, you will see the Video Server S shortcut icon on the desktop. For the latest AP software updates,

4. Enter User ID, password, IP address and port 8000. Click on green button and you should see live video.Remote Video Server LOGIN WINDOW Address

h. System Confi g : Allows you to confi gure Network, DVR, Alarm and General settings. Very powerful tool for remote control of your DVR. Will

7.7 System Confi g : Allows you to remotely confi gure Network, DVR, Alarm and General settings. Double click on System Confi g7.8 NETWORK: The networ

• PPPoE: PPPOE stands for Point-to-Point Protocol over Ethernet. Obtain ADSL service from ISP. Obtain and install PPPoE software. Choose

DVR: Selecting DVR will allow you to make changes to cameras, motion, create backup fi les, search fi le options, schedule recording and record setting

Select AREA to setup motion area.a. DETECT (motion detection): Select motion detection function ON / OFF.b. AREA (motion detection area):

After pressing “Start”, “Write CD Setting” pop-up window will display. Select “Close Disc” if your done burning. Select “Append Player” to install

7.13 Search List Quickly search the event logs from 4 different recording types, and backup the event recording. 1. Manual 2.

1. OVERVIEW1.1 General Information• Video Compression Frame: MJPEG ; • Format

Press Apply to create backup fi leUse Video Backup Player to view backup fi le7.14 Timer Record Timer Record”, you can schedule up to 7 time even

7.15 Date Set the date for your DVR. DO NOT change the date or time when the recording. • DATE Select the current date from “DATE”

7.17 AlarmEnable of disable email or ftp and fi le back up alarm notifi cation.• Alarm Trigger Enable or Disable alarm trigger.• Alarm Method Sele

7.19 Account View the account information, set the maximum user number, and add / delete / edit user accounts.• Set the maximum number o

7.22 Operation via IE BrowserYou can view the images or operate your DVR using a IE (Internet Explorer) web browser. Note: Operating systems that su

8.0 Remote PTZ Camera Control Panela ~ i: Same as the DVR control panel a ~ i.J. Preset 1 ~ 16 Use Preset 1 ~ 16 positions to pre-defi ned camera

9.0 FAQ/ TROUBLESHOOTINGPlease refer to the table below when troubleshooting. Problem

9.1 Default ValuesDVR Item Default ValueADMIN Password 0000 Detection OFFGUEST Password 1

Appendix 2 DVQ-2, DMR 4 RT Pin Confi gurationEXTERNAL DEVICESConnecting External Alarms devices - example using a Siren: Use pins 7, 8 inputs and 15 CO

9 GND Signal GND10 RS485-B DVR pin is used to serially communicate with remote PC using the RS-485 PROTOCOL. 11 RS485-A DVR pin is used to serial

71.3 Package Contents• DVQ unit × 1• Power Supply × 1• Power Cable × 1• Manual × 1• Software CD-R × 1ORPower cordPower supplySoftwareManualDVQ-2DMR 4,

Appendix 2 DMR 8, 16 RT Pin Confi gurationPIN DESCRIPTIONPIN NUMBERS:1 GND Earth GND2 ~ 9 ALARM INPUT Use ALARM INPUT ( PINS 2 -- 9 ) and GND

Appendix 3, DVQ-2 & DMR 4, 8, 16 RT RS232 PROTOCOLData: REMOTE PROTOCOL use 8 bit data, 1 start bit, 1 stop bit.71

Appendix 4, DVQ-2 RECORDING TIME TABLE72

Appendix 5, DVQ-2 Compatible USB Flash Drives.Upgrade to the latest DVR fi rmware version. If the USB fl ash drive is not supported by the DVR will not

Appendix 6, DMR 4, 8, 16 RT Compatible Hard Drives HDD.74

Appendix 7, DVQ-2 & DMR 4, 8, 16 RT MENU TREE75

Appendix 8 DMR 4, 8, 16 RT Specifi cations76

Appendix 8 DMR 4, 8, 16 RT Specifi cations77

Appendix 11DVQ-2 Specifi cations78

2. FRONT AND REAR PANELS2.1 Front Panels8PowerMenuLeft, Right keys SearchUp, Down keysEnter key Plus +, Minus - keysDVQ-2DMR 4, 8, 16 RT

1) LED Indicators The following LEDs will be on when: • HDD (Hard Drive): HDD is reading or recording • HDD Full: HDD is full. • ALAR